IJH_2026v16n5

International Journal of Horticulture, 2026, Vol.16, No.5, 331-337 http://hortherbpublisher.com/index.php/ijh 334 3 Results and Analysis 3.1 Spawn run, pinhead initiation, and harvesting time Spawn rate had a highly significant effect on the duration of mycelial colonization and the developmental stages that followed it (Table 1). Raising the spawn rate from 4% to 12% progressively shortened the spawn run period, though the rate of improvement clearly diminished beyond 10%. T4 andT5 were statistically at par across all three timing parameters, pointing to diminishing returns beyond the farmer-practice spawn rate (see Section 4.1 for interpretation). Table 1 Effect of spawn rate on spawn run, pinhead initiation, and first harvest Treatment Spawn run (days) Pinhead initiation (days) First harvest (days) T1 (4%) 24.5±0.47a 29.2±0.52a 34.6±0.55a T2 (6%) 21.8±0.47b 26.4±0.52b 31.7±0.55b T3 (8%) 18.3±0.47c 23.1±0.52c 28.2±0.55c T4 (10%, farmer practice) 16.6±0.47cd 21.5±0.52cd 26.6±0.55cd T5 (12%) 15.9±0.47d 20.8±0.52d 26.0±0.55d F-value 59.78*** 45.41*** 43.83*** p-value <0.001 <0.001 <0.001 CV(%) 4.31 3.86 3.51 Grandmean 19.42 24.20 29.42 Note: Means in a column followed by different lowercase letters differ significantly at p ≤ 0.05 (DMRT). ** p ≤ 0.01; *** p ≤0.001. SE: standard error (n = 4); CV: coefficient of variation 3.2 Number of fruiting bodies, cap diameter, and stipe length Spawn rate significantly influenced all three morphological parameters (Table 2). The number of fruiting bodies per bag rose consistently with spawn rate, while average cap diameter and stipe length moved in the opposite direction, shrinking as fruiting-body density increased. T4 andT5 produced statistically similar numbers of fruiting bodies, both well ahead of the lower spawn rates. Even so, both treatments produced smaller, thinner fruiting bodies than T1 andT2 a size-number trade-off discussed further in Section 4.2. Table 2 Effect of spawn rate on fruiting body number, cap diameter, and stipe length Treatment Fruiting bodies (No./bag) Cap diameter (cm) Stipe length (cm) T1 (4%) 24.3±0.95d 5.8±0.21a 4.9±0.18a T2 (6%) 29.1±0.95c 5.4±0.21ab 4.5±0.18ab T3 (8%) 34.8±0.95b 5.0±0.21b 4.0±0.18b T4 (10%, farmer practice) 38.2±0.95a 4.6±0.21bc 3.6±0.18bc T5 (12%) 39.0±0.95a 4.1±0.21c 3.2±0.18c F-value 43.34*** 10.45*** 14.43*** p-value <0.001 <0.001 <0.001 CV(%) 6.02 7.44 8.11 Grandmean 33.08 4.98 4.04 Note: Means in a column followed by different lowercase letters differ significantly at p ≤ 0.05 (DMRT). ** p ≤ 0.01; *** p ≤0.001. SE: standard error (n = 4); CV: coefficient of variation 3.3 Yield, biological efficiency, and contamination Total fresh yield and biological efficiency followed the same upward trend as fruiting body number, while contamination incidence fell sharply as spawn rate increased (Table 3). Yield and biological efficiency at T4 (10%) and T5 (12%) were statistically indistinguishable, both significantly exceeding T1, T2, and T3. Contamination was observed only at the two lowest spawn rates: one of four bags at T1 (25%) and one of eight cumulative bag-observations at T2 (12.5%) showed visible green mold before spawn run completion, whereas no contamination at all was recorded at 8% spawn rate or above (interpreted further in Section 4.2).

RkJQdWJsaXNoZXIy MjQ4ODYzNA==